An AC108-2MB-2UQ01 With a 5-Pin + 2-Pin Plug: What We Found
Share
Every so often a repair turns up a part that isn't supposed to exist. This is one of those cases, and it's worth writing down: the switch is in circulation, and the model number on its label is misleading.
A customer sent us photos from a sofa repair — a five-button Mulin switch labeled AC108-2MB-2UQ01, with USB-A and USB-C ports, but with a plug setup we had never seen on that model. We sent the photos to the manufacturer. Mulin's answer was short: they have never produced an AC108-2MB-2UQ01 like this.
Here is what we know, what probably happened, and the switch to use if you can't find an original.
The short version
- The catalog version of the AC108-2MB-2UQ01 has a single 5-pin plug.
- The unit found in the field is labeled AC108-2MB-2UQ01 but has a 5-pin right-angle male plug plus a 2-pin female plug.
- Mulin confirmed it has never produced this version.
- The likely explanations are a small sample run or a label applied to the wrong switch upstream. Neither is confirmed.
- For a replacement, the 23300295X000 uses the same plug types and has close mounting dimensions.
- Check the plugs and measure the mounting points before ordering. On this unit, the label is not enough.
What the customer found
The switch came out of a power recliner during a repair. The label is legible: Model AC108-2MB-2UQ01, input DC 29V, USB output 18W, date code 2024-12-26. The housing, the five buttons, and the charging ports all match the AC108 we know.
The plugs do not match. Where a standard AC108 ends in a single 5-pin connector, this unit ends in two:
- a right-angle 5-pin male plug, on a cable tagged FOOTREST in the photo;
- a 2-pin female plug, on a cable tagged HEADREST.
Two connectors, two motor circuits, one label that says AC108.
What the standard part looks like
The AC108-2MB-2UQ01 we stock is a five-button switch with USB-A and USB-C ports, 29V DC input, and 18W USB output. It ends in one 5-pin plug. That is the version in the Mulin catalog, and every unit we have handled matches it.
That photo is also the reason the substitution later in this article works. The two switches are close in the dimensions that decide whether a part drops into an existing cutout: the mounting hole spacing and the size of the installation block behind the faceplate.
What the manufacturer said
We sent the label and plug photos to Mulin. Their response: they have not produced an AC108-2MB-2UQ01 with this plug configuration. That rules out a running design change on this model, at least as far as the factory is concerned.
Two plausible explanations
Neither of these is confirmed. Both fit the evidence.
1. A small sample or prototype batch. When a furniture factory develops a new chair, the switch supplier may build a small run to that factory's wiring spec — sometimes in a different housing, or with extra connectors — before the catalog part is finalized. Sample units occasionally end up in production sofas or in the aftermarket, label and all.
2. A label applied to the wrong switch upstream. The 5-pin + 2-pin layout is exactly what the 23300295X000 uses: its right-angle 5-pin plug feeds the footrest motor, and its 2-pin plug feeds the headrest motor. If an AC108 label went onto a switch built for that wiring, the result would look exactly like the unit in the photos. Mislabeling at OEM and subcontractor level happens more often than most people expect.
That second explanation is circumstantial, not proof. But it fits everything we can see: same label, same button layout, different connectors.
Either way, the practical conclusion is the same. On this unit the label and the hardware disagree, and the hardware is what plugs into the chair.
At a glance
| AC108-2MB-2UQ01, catalog version | Unit found in the field | 23300295X000 | |
|---|---|---|---|
| Plugs | One 5-pin plug | 5-pin right-angle male + 2-pin female | 5-pin right-angle male + 2-pin female |
| Buttons | Five | Five | Five |
| Charging ports | USB-A + USB-C | USB-A + USB-C | USB-A + USB-C |
| Rated input | 29V DC | 29V DC | 29V 2A |
| USB output | 18W (per label) | 18W (per label) | 5V 2.1A |
| Availability | In stock | Not produced, per Mulin | In stock |
Why this matters when you order
Most recliner switch listings, ours included, tell you to match the model number. For the vast majority of repairs that works. This case is the exception: the model number on the label does not guarantee the plug configuration.
If you order a standard AC108-2MB-2UQ01 for a chair wired for two connectors, you get one plug where the harness expects two. The headrest circuit has nothing to plug into, and the switch will not do the job even though the label matches.
So check the plugs, not just the number.
The switch to use instead: 23300295X000
If you have the two-plug version and no original is available, the 23300295X000 is the closest match we carry. It is also a Mulin switch — model WPS5C10071 — and it is built around the same connector set as the unit in the photos:
- a right-angle 5-pin male plug for the footrest motor;
- a 2-pin female plug for the headrest motor;
- five buttons: chair open and close, headrest forward and back, and a round reset button for the headrest and footrest;
- USB-A and USB-C charging ports, 29V 2A input, 5V 2.1A USB output;
- mounting hole distance and installation block dimensions close to the AC108's.
One caveat, stated plainly: this is a physical match, not an official cross-reference from Mulin. The 23300295X000 has its own part number and model number, and the two switches are not interchangeable in every chair. Measure before you order.
Before you order: five checks
- Read the label. Model number, date code, voltage, USB output. Photograph it before the switch goes back into the chair.
- Count the plugs. One 5-pin plug means the standard AC108-2MB-2UQ01. A 5-pin plus a 2-pin means you have the version in this article.
- Measure the mounting points. Center-to-center distance between the mounting holes, plus the length, width, and height of the installation block. "Similar" is not "identical".
- Look at the chair's harness. The 2-pin headrest connector has to exist on the chair side, not just on the switch.
- Check the ports and output. The AC108 label says 18W USB output; the 23300295X000 is rated 5V 2.1A. If you rely on fast charging, that difference matters.
If any of this is unclear, send us photos of the label, the plugs, and the mounting hole spacing. We will tell you which switch you have.
FAQ
Is every AC108-2MB-2UQ01 a single 5-pin plug?
As far as we and the manufacturer know, yes. This unit is the first exception we have seen, and Mulin says it did not build it.
Does that mean the switch is counterfeit?
Not necessarily. A sample run or a misapplied label explains it without anyone deliberately copying anything. What we can say is that the label and the plugs do not match.
Can I use a standard AC108-2MB-2UQ01 instead?
Only if your chair has a single 5-pin mating connector and the button functions match. If your harness has a separate 2-pin headrest connector, it will not work.
Will the 23300295X000 fit?
It fits when the chair uses the same 5-pin + 2-pin layout and the mounting dimensions are close. Measure the hole spacing and the installation block first; the two parts are similar, not identical.
The label is gone. How do I identify the switch?
Compare the plug types, button count, button functions, and mounting pattern. Photos of the old switch next to a ruler are the fastest way to get an answer.
Bottom line
A switch labeled AC108-2MB-2UQ01 with a 5-pin right-angle male plug and a 2-pin female plug is not a catalog part — Mulin has confirmed it never made one. Treat the label as unreliable on this unit and match the hardware instead. If you need a replacement, the 23300295X000 is the closest match we carry for that connector layout.
Both switches are linked below.
Mulin AC108-2MB-2UQ01 5-button switch — for chairs wired for a single 5-pin plug. Five buttons, USB-A and USB-C charging.
23300295X000 five-button switch — for chairs wired for a 5-pin + 2-pin pair. Five buttons, USB-A and USB-C charging.
Found a switch that doesn't match its label? Send photos of the label, both plug ends, and the mounting hole spacing, and we will help you work out what you have.